Clik here to view.
Wiki Page: Model Pipe resting on the seabed floor - AutoPIPE
Applies To Product(s):AutoPIPE,Version(s):2004, XM, & V8iEnvironment: N/AArea: modelingSubarea: Original Author:Bentley Technical Support GroupProblem:AutoPIPE: model pipe on seabead floorSeabed...
View ArticleForum Post: Re: "Thermal" combination
Hello Mykola, As mentioned in the online help:The "Non-Code" grid displays the active load case combination set defined for any purpose other than code compliance (e.g. displacement and support...
View ArticleForum Post: Re: No of Mode Shapes for Modal Analysis
Hello Pssrijit,Mykola was correct. In order to create addtional modes increae the modal analysis setting Loads> Dynamic Analysis> Maximum number of modes. See online help for more information on...
View ArticleClik here to view.
Wiki Page: Pipe and Piping Compoents Enhancements for AutoPIPE
Applies To Product(s):AutoPIPE,Version(s):2004, XM, & V8iEnvironment: N/AArea: EnhancementSubarea: Original Author:Bentley Technical Support Group The following enhancements have already been...
View ArticleClik here to view.
Wiki Page: Modeling Approaches, Tips, Technique for Bend Piping Components in...
Applies To Product(s):AutoPIPE,Version(s):2004, XM, & V8iEnvironment: N/AArea: ModelingSubarea: Original Author:Bentley Technical Support GroupAttention: Please see the following AutoPIPE help...
View ArticleClik here to view.
Wiki Page: Import and Export - AutoPIPE
Topics under the heading should be based on:All translator and integration issues, including PipeLink, Caesar, OpenPlant, MDB, NTL etc.Import Issues:AutoPIPE CAD To Stress Integration [TN]ADLPipe...
View ArticleClik here to view.
Wiki Page: Interface bewteen Projectwise and AutoPIPE
Applies To Product(s):AutoPIPE,Version(s):2004, XM, & V8iEnvironment: N/AArea: Inport/ExportSubarea: Original Author:Bentley Technical Support GroupComments, Questions, and AnswersHow to associate...
View ArticleClik here to view.
Wiki Page: Model Different Types of PIPING in AutoPIPE
Applies To Product(s):AutoPIPE,Version(s):2004, XM, & V8iEnvironment: N/AArea: ModelingSubarea: Original Author:Bentley Technical Support GroupProblem:What are some typical modeling approaches for...
View ArticleClik here to view.
Wiki Page: Bentley AutoPIPE Vessel
Topics under the heading should be based on:Bentley AutoPIPE VesselAutoPIPE Vessel Software Release NotesInstallationError / Warning MessagesFAQ
View ArticleClik here to view.
Wiki Page: ASME B31.3 Piping Code Calcualtion Issues
Comments, Questions, and Answers Question: I am trying to verify pressure extension result in AutoPIPE 09.04.01.05 using hand calculation. Could you please provide the formulas used in AutoPIPE for...
View ArticleClik here to view.
Wiki Page: Modeling - AutoPIPE
Topics under the heading should be based on:Component modeling with associated dialogs**Attention** Please see the following AutoPIPE help section: Help > Contents> Contents Tab> Modeling...
View ArticleClik here to view.
Wiki Page: Model Soil Properties in AutoPIPE
Applies To Product(s):AutoPIPE,Version(s):2004, XM, & V8iEnvironment: N/AArea: ModelingSubarea: Original Author:Bentley Technical Support GroupAttention: Please see the following AutoPIPE help...
View ArticleClik here to view.
Wiki Page: StressISO - AutoPIPE
Topics under the heading should be based on:StressISO Attention: Review the following file installed with AutoPIPE (search hard drive):C:\ Bentley \AutoPIPE V8i SELECTseries...
View ArticleClik here to view.
Wiki Page: Stress Iso Configuration files
Applies To Product(s):AutoPIPE,Version(s):2004, XM, & V8iEnvironment: N/AArea: ExportSubarea: Original Author:Bentley Technical Support GroupThe customizable Stress Isometric plot is created using...
View ArticleForum Post: Re: Pressure Extension
The equations mentioned for axial pressure elongation assume large D/t ratio for pipes or thin wall pipes. AutoPIPE uses the more accurate large thickness formula and hence the slight difference....
View ArticleForum Post: The Best of Jessica's Blog on Insider Skills this Friday (9/13)
Join Jessica as she shows you live some of the different topics she has blogged about recently.Topics will include:SegmentsInput/Results GridsUseful View Toolbar CommandsScale Function Click here for...
View ArticleForum Post: Training for AutoPIPE Vessel
Hit the ground running with the recent release of AutoPIPE Vessel with Live Training!Monday September 30th AutoPIPE Vessel Fundamentals Click Here to RegisterWe hope to see you there!
View ArticleForum Post: Re: Thermal range
Are you asking how to update the temperature case for a particular section? If so, just highlight the area you are wanting to change, then go to Insert > Operating Pressure & TemperatureThis...
View ArticleClik here to view.
Wiki Page: Calculations in PULS
Topics under the heading should be based on:Calculations in PULS**Attention** Please see the following AutoPIPE help section:Help > Contents> Reference>This page provides references used in...
View Article