Wiki Page: GrayLoc Connector Piping Components - Modeling Approaches, Tips,...
Applies To Product(s): AutoPIPE, Version(s): 2004, XM, & V8i Environment: N/A Area: model Subarea: Original Author: Bentley Technical Support Group Problem: How to model Greyloc connectors in...
View ArticleWiki Page: Bend & Miter Piping Components - Modeling Approaches, Tips,...
Applies To Product(s): AutoPIPE, Version(s): 2004, XM, & V8i Environment: N/A Area: Modeling Subarea: Original Author: Bentley Technical Support Group Attention: Please see the following AutoPIPE...
View ArticleWiki Page: Flanges Piping Components - Modeling Approaches, Tips, Techniques...
Applies To Product(s): AutoPIPE, Version(s): 2004, XM, & V8i Environment: N/A Area: Modeling Subarea: Original Author: Bentley Technical Support Group Attention: Please see the following AutoPIPE...
View ArticleWiki Page: Orifice Type Piping Components - Modeling Approaches, Tips,...
Applies To Product(s): AutoPIPE, Version(s): 2004, XM, & V8i Environment: N/A Area: Modeling Subarea: Original Author: Bentley Technical Support Group Problem: How to model Orifice type piping...
View ArticleWiki Page: Model Different Types of PIPING Components - AutoPIPE
Applies To Product(s): AutoPIPE, Version(s): 2004, XM, & V8i Environment: N/A Area: Modeling Subarea: Original Author: Bentley Technical Support Group Attention: Please see the following AutoPIPE...
View ArticleWiki Page: ASCE7 - 2010 Wind loads are Service or Ultimate loads in AutoPIPE
Applies To Product(s): AutoPIPE, Version(s): 2004, XM, & V8i Environment: N/A Area: Subarea: Original Author: Bentley Technical Support Group Problem: Up 'til now, we had been using ASCE 7-02...
View ArticleWiki Page: "Wind" - AutoPIPE Load Case
Applies To Product(s): AutoPIPE, Version(s): 2004, XM, & V8i Environment: N/A Area: Load Case Subarea: Original Author: Bentley Technical Support Group Comments Questions and Answers about Wind...
View ArticleWiki Page: Results Post Processing in AutoPIPE
Applies To Product(s): AutoPIPE, Version(s): 2004, XM, & V8i Environment: N/A Area: Results Subarea: Original Author: Bentley Technical Support Group Comments, Questions, and Answers on results:...
View ArticleWiki Page: Forces and Moments Output Report results for an Anchor node point...
Applies To Product(s): AutoPIPE, Version(s): 2004, XM, & V8i Environment: N/A Area: Subarea: Original Author: Bentley Technical Support Group Problem: At a pipe end point, actually a weld neck...
View ArticleWiki Page: Forces and Moments report results when a flange is added in AutoPIPE
Applies To Product(s): AutoPIPE, Version(s): 2004, XM, & V8i Environment: N/A Area: Reports Subarea: Original Author: Bentley Technical Support Group Problem: The results from the following 3...
View ArticleWiki Page: Forces and Moments results summation about a TEE in AutoPIPE
Applies To Product(s): AutoPIPE, Version(s): 2004, XM, & V8i Environment: N/A Area: Report Subarea: Original Author: Bentley Technical Support Group Problem: If I wanted to run a separate analysis...
View ArticleForum Post: H/D greater than 14
Please provide detail for a buried system, received message stating H/D is greater than 14, why H/D not to exceed 14? If Height is what is provided, and diameter of pipe is fixed, what can be done?
View ArticleForum Post: ASME B31.8-2012, paragraph 833.3 how i can includes this in to...
I’m Stress Analyst Jr. I have some problems with the code ASME B31.8 into de paragraph 833.3, The net longitudinal stress in restrained pipe? and how i can reported an Analysis Von Misses or Tresca?...
View ArticleWiki Page: 3. "The Gasket Material [SPIRAL-WOUND ALLOY WITH MINERAL FIBER...
Applies To Product(s): AutoPIPE, Version(s): 2004, XM, & V8i Environment: N/A Area: Message Subarea: Original Author: Bentley Technical Support Group Nov 2014, AutoPIPE V8i 09.06.01.10 Problem: The...
View ArticleWiki Page: 2. "The required information is missing for this flange" - Bentley...
Applies To Product(s): AutoPIPE, Version(s): 2004, XM, & V8i Environment: N/A Area: Message Subarea: Original Author: Bentley Technical Support Group Nov 2014, AutoPIPE V8i 09.06.01.10 Problem: The...
View ArticleWiki Page: 1. "Query is too complex" - Bentley AutoPIPE messge
Applies To Product(s): AutoPIPE, Version(s): 2004, XM, & V8i Environment: N/A Area: Subarea: Original Author: Bentley Technical Support Group Nov 2014, AutoPIPE V8i 09.06.01.10 Problem: The...
View ArticleWiki Page: 4. "H/D is greater than 14.0" - Bentley Message displayed in AutoPIPE
Applies To Product(s): AutoPIPE, Version(s): 2004, XM, & V8i Environment: N/A Area: Subarea: Original Author: Bentley Technical Support Group Problem: The following is displayed when entering data...
View ArticleWiki Page: "Bentley AutoPIPE" Messages displayed in AutoPIPE
Applies To Product(s): AutoPIPE, Version(s): 2004, XM, & V8i Environment: N/A Area: Error Messages Subarea: Original Author: Bentley Technical Support Group 1. Query is too complex 2. The required...
View ArticleForum Post: RE: H/D greater than 14
Hello Perma: With regards to your post, see the following Bentley Communities web page: http://communities.bentley.com/ Place your cursor in the Search Field and type "AutoPIPE Bentley Messages ", and...
View ArticleOutput Report in AutoPIPE">Wiki Page: "Forces & Moments" sub-report using Results> Output Report in...
Applies To Product(s): AutoPIPE, Version(s): 2004, XM, & V8i Environment: N/A Area: Subarea: Original Author: Bentley Technical Support Group Comments, Questions, and Answers about AutoPIPE's...
View Article