Forum Post: RE: copying and pasting into a file changing the load cases
Robert Herrick, Please provide an exact set of steps to repeat for better understanding of your issue. Thanks for your time. Regards, Mike Dattilio Bentley Systems Design Analyst Design Engineering...
View ArticleForum Post: RE: Degree of Freedom for a beam structure
I loaded the image file in "secured file upload". I am not sure why the file does not show. I did that again today.
View ArticleForum Post: RE: Degree of Freedom for a beam structure
I loaded the image file in "secured file upload". I am not sure why the file does not show. I did that again today.
View ArticleForum Post: How to apply CSA N289.3 rules for NC piping ?
How to apply CSA N289.3 rules for the piping designed to ASME Boiler & Pressure Vessel Code Section III Subsection NC rule in Autopipe ? And what are the differences between N289.3 and NC seismic...
View ArticleWiki Page: Q. Change AutoPIPE Edition License to: (Standard, Advanced, Nuclear)
AutoPIPE will default to Demo mode when the application is first installed, the user must then change the edition setting on the "Welcome to AutoPIPE Licensing" dialog. This dialog will automatically...
View ArticleForum Post: RE: How to creat this mode.
Good day to you Zhu Jun, Is this a heat exchanger or a pipe welded into the end of a vessel Are you using AutoPIPE or AutoPIPE Vessel? If using AutoPIPE, continue below. 1. Model large vessel piping....
View ArticleForum Post: RE: Pressure thrust at flexible joint
Good day to you Manoj Kumar, You have identified how much movement is to be absorbed by your flexible joint. Suggest that you contact your Flexible Joint supplier to ask them which joint is best suited...
View ArticleWiki Page: 01. Floating Interactive F3 Results Dialog (Point Result...
Comments, Questions and Answers This is a floating dialog that displays specific results information about the current selected node point. This dialog is displayed in AutoPIPE V8i 09.06.xx.xx and...
View ArticleWiki Page: 06. Floating Interactive F3 Results Dialog missing from view in...
Applies To Product(s): AutoPIPE Version(s): ALL; Area: Results Date Logged & Current Version Dec 2019 12.02.00.14 Problem: When I click on the pipe support and want to see forces & moments at...
View ArticleWiki Page: 01. How to print parts of the model highlighted red color only in...
Applies To Product(s): AutoPIPE Version(s): 2004, XM, V8i Area: Printing Original Author: Bentley Technical Support Group Date Logged & Current Version Feb. 2015 09.06.01.10 Problem: How to print...
View ArticleWiki Page: 02. How can I search for a all the node points that exceed a...
Applies To Product(s): AutoPIPE Version(s): 2004, XM, V8i Area: Report Original Author: Bentley Technical Support Group Date Logged & Current Version Feb. 2015 09.06.01.10 Problem: How can I search...
View ArticleWiki Page: 04. How to print out / save the AutoPIPE code stress color map?
Applies To Product(s): AutoPIPE Version(s): ALL Area: Print/Plot Original Author: Bentley Technical Support Group Date Logged & Current Version Feb. 2015 09.06.01.10 Problem: How to print out /...
View ArticleWiki Page: 03. When user prints to Adobe PDF from AutoPIPE, numbers on...
Applies To Product(s): AutoPIPE Version(s): 2004, XM, V8i Area: Print Original Author: Bentley Technical Support Group Date Logged & Current Version Feb. 2015 09.06.01.10 Problem: When user prints...
View ArticleWiki Page: 06. The cover page and table of contents page in the AutoPIPE...
Applies To Product(s): AutoPIPE Version(s): 2004, XM, V8i Area: Report Original Author: Bentley Technical Support Group Date Logged & Current Version Sept. 2015 09.06.02.06 Problem: We’re having an...
View ArticleWiki Page: 05. Printing the AutoPIPE output report, either on paper or PDF,...
Applies To Product(s): AutoPIPE Version(s): 2004, XM, V8i Area: Report Original Author: Bentley Technical Support Group Date Logged & Current Version April. 2015 09.06.02.06 Problem: Printing the...
View ArticleWiki Page: 09. What is the information reported on the first 2 lines of the...
Applies To Product(s): AutoPIPE Version(s): ALL; Area: Report Date Logged & Current Version April. 2018 11.02.00.10 Problem: What is the information reported on the first 2 lines of the...
View ArticleForum Post: RE: Quarterly usage in AutoPIPE
They can't just work on the software -> create overuse -> get invoice from Bentley?
View ArticleForum Post: RE: How to apply CSA N289.3 rules for NC piping ?
Hello Geping The implementation of CSA N289.3 in to AutoPIPE required only program changes for B31.1 (settings in the Results Options) and ASME NB (Stress Summary). The requirement for NC/ND don't...
View ArticleForum Post: RE: ASME I - BOILER DESIGN
Unfortunately no AutoPIPE Vessel does not design boilers because those designs do not have an industrial standard for construction unlike TEMA for shell and tube heat exchangers. Most boilers have...
View ArticleForum Post: RE: Autopipe Vessel gasket width error 356
Will you please submit a service request with your model attached and we can investigate further.
View Article