Wiki Page: 04. Confirm the license change
Applies To Product(s): AutoPIPE Vessel Version(s): ALL Area: Licensing Date Logged & Current Version May 2019 41.01.00.005 Problem: The following appears when changing licensing settings: why?...
View ArticleWiki Page: Warning Messages
01. 159: Nozzles: no verification on multiple openings. warning message in AutoPIPE Vessel 02. 604 Unit Distortions on Nozzles (L001): PD 5500 Figure G.2.2-19 deflections of cyl. shells due to radial...
View ArticleWiki Page: 08. HP Connection Manager Fatal Error
Applies To Product(s): AutoPIPE Vessel Version(s): ALL Area: Install Date Logged & Current Version June 2018 40.06.00.07 Problem: The following dialog appears when starting the application: German:...
View ArticleWiki Page: IDispatch::Invoke("LoadArx"=00000013) failed w/err 0x80020009
Comments, Questions, and Answers related to AutoWrap() Messages in AutoPIPE Vessel Problem: User starts the program, then chooses Execute Strength Calculation option which ends with no error. In the...
View ArticleWiki Page: 09. Intel(r) Visual Fortran Run-time Error - forrtl servere (408):...
Applies To Product(s): AutoPIPE Vessel Version(s): ALL Area: Crashed Date Logged & Current Version March 2018 40.06.00.07 Problem: The following appears when using AutoPIPE Vessel: forrtl servere...
View ArticleWiki Page: 10. Intel(r) Visual Fortran Run-time Error - forrtl: severe (408):...
Applies To Product(s): AutoPIPE Vessel Version(s): ALL Area: Crashed Date Logged & Current Version Aug 2018 40.07.00.007 Problem: The following appears when using AutoPIPE Vessel: forrtl: severe...
View ArticleWiki Page: Application Crash Messages
01. The application crashes when running the Strength calculations, why and how to avoid when using AutoPIPE Vessel? 02. Application graphic screen and license dialog are blank when starting AutoPIPE...
View ArticleWiki Page: 28. Results are different for nozzles when using AutoPIPE Vessel...
Answer: One change that may answer the discrepancy between the models is that the calculation of the weight of nozzle necks has been optimized in September 2012 (v33.0.7.3) to consider the intersection...
View ArticleWiki Page: Nozzles and Flanges
01. Flange Optimization 02. Flange Bolt Tensioning 03. Flange calculations does not consider corrosion allowance and the flange facing height in AutoPIPE Vessel, why? 04. How to modify the external...
View ArticleWiki Page: 27. Earthquake load cases results are not reported
Furthermore, it would seem to be an error in the calculation of yC: yC = m + E + m + H/2 in the edition of the results. Should be rather considered yC = m + E + m + (H - m) / 2 Answer: The development...
View ArticleWiki Page: Loads and Load Combinations
01. Adding a Snow Load 02. Design vs Design Check in AutoPIPE Vessel? 03. How to combine the Wind loads and Seismic loads in an AutoPIPE Vessel combination / analysis? 04. How to Define Multiple Load...
View ArticleWiki Page: 26. Error in the calculation of yC: yC = m + E + m + H/2 in the...
Answer: There would be the error in calculation of yC because there is no weld at the top of the sail.
View ArticleWiki Page: Calculations
01. What is the formula used for hydro-test pressure calculations per CODAP Div. 1 used for Shell and Tube Heat Exchangers in AutoPIPE Vessel? 02. How to check for bolt load calculations for...
View ArticleWiki Page: 44. What is the critical value of half angle at skirt apex...
Answer: There is nothing in GOST R51274-99.8 to limit the half apex angle of the skirt. But this is a usual rule, this limitation exists in AD S3/1 4.2 and in CODAP C9.7.1. (French code) to avoid the...
View ArticleWiki Page: 45. What is the required thickness for the longitudinal stresses...
Answer: According to the ASME VIII Div.1 the minimum thickness shall be the greater thickness as given by the circumferential stress UG-27(c)(1) or longitudinal stress (c)(2). The thickness due to the...
View ArticleWiki Page: Pressure Vessels
01. How to optimize Body flange design in AutoPIPE Vessel? 02. Number of bolts required for design using AutoPIPE Vessel 03. On Body flange tab, why the calculation of bolts is set by default on the...
View ArticleForum Post: RE: AutoPIPE
I am guessing AutoPIPE can be run in all three modes. I would contact Bentley directly to see how to set up AutoPIPE to meet your needs.
View ArticleWiki Page: License AutoPIPE -
In order to license Bentley AutoPIPE, AutoPIPE Vessel, and/or AutoPIPE Nozzle, users must set up licensing in 2 locations: 1. Inside of the application - click here 2. Outside of the application -...
View ArticleWiki Page: Q. How to log a Service Request using AutoPIPE?
Follow these instructions: 1. With AutoPIPE open, select HELP> Technical Support Note : AutoPIPE CONNECT 10.01.xx.xx and lower link has been updated to: https://apps.bentley.com/srmanager/ (D567222)...
View ArticleWiki Page: - CONNECTION Client - AutoPIPE
Bentley communities site Typical Questions Q. What is CONNECTION Client Q. Download CONNECTION Client Release notes Q. Open CONNECTION Client Install issues: > Click on the CONNECTION Client...
View Article