Forum Post: RE: Fluid Transient Flow Rate
Greetings Jeff Webb, Please note that all of the examples in AutoPIPE help and workbooks are fictious. T hey are all just made up scenarios to train users on how to use the program. Furthermore, all of...
View ArticleForum Post: RE: V23.0 and B31E
Greetings Kevink, To be 100% clear, I believe that you are talking about adding more than 1 row for each case imaged below, correct? If yes , the short answer is No, there is only one level at this...
View ArticleForum Post: RE: EN13480 code stress combinations for occasional displacements
Greetings Daniel Finn, Please note that AutoPIPE only understands that the U1..Uxx is a load case. It does not know exactly what it represents. Therefore is treated as an occasional load and auto...
View ArticleForum Post: Validation of Autopipe connect edition
Is there any validation documents that shows autopipe connect edition can be used with GB/T 20801 OR SIMILIAR?
View ArticleWiki Page: 03. Bentley AutoPIPE Acceptance Test Set (ATS)
The Bentley AutoPIPE Acceptance Test Set (ATS) provides the user with a recommended procedure for validating the integrity of an installed AutoPIPE QA & Report subscription service version of the...
View ArticleWiki Page: Q. Where to download ATS for a certain version of AutoPIPE?
Answer: Are you a part of the QA program? IF no, you can either: a. use the ITS ( see here ) or b. become a QA program member, contact Joanie Mayberry , requesting instructions on how to join the QA...
View ArticleForum Post: RE: License: AutoPIPE vs. AutoPIPE Advanced
Thank you for responding. I ask this question on behalf of our client. They received the Invoice QTL. Maybe it's because they used AutoPIPE advance and AutoPIPE standard at the same time. They want to...
View ArticleForum Post: RE: multiple skirt opening
Greetings, Unfortunately there is no separate nozzle opening provision available in software. But you can use vents & skirt access opening as nozzle openings. If you want these two separately...
View ArticleForum Post: RE: AutoPIPE - Flow Induced Vibration
Greetings, Flow induced vibration analysis can be performed if we get the harmonic loads generated from unbalanced rotating equipment, acoustic vibrations caused by reciprocating equipment, flow...
View ArticleForum Post: RE: vibration analysis
Greetings, Flow induced vibration analysis and Acoustic Induced vibration can be performed if we get the harmonic loads generated from unbalanced rotating equipment, acoustic vibrations caused by...
View ArticleForum Post: RE: License: AutoPIPE vs. AutoPIPE Advanced
Greetings Tai Huy, The best method of understanding the difference between AutoPIPE's 3 different license levels (as mentioned on WIKI above), Please see the following AutoPIPE help section: Help >...
View ArticleWiki Page: AutoPIPE QA&R program
Q1. Who can I contact with any questions regarding the AutoPIPE QA&R (Quality Assurance and Reporting) program? Answer: 1. QA&R Program Manager: Bruce Bader. email: Bruce.Bader@bentley.com 2....
View ArticleForum Post: RE: Validation of Autopipe connect edition
Greetings, Please see WIKI here , This will provide details of validation documents available for Bentley AutoPIPE. Regards, Mike Dattilio Design Analysis Engineering Group Senior Analyst Bentley...
View ArticleForum Post: Release for hanger selection
What is the impact for the pipe installer "release for hanger selection" is checked?
View ArticleForum Post: RE: Release for hanger selection
To elaborate: It is my understanding when sizing springs with the "release for hanger selection" checked, AutoPIPE treats the anchor as being free (in the selected degrees-of-freedom) during sizing....
View ArticleWiki Page: Q. Trial mode displayed on BLT for AutoPIPE license, why and how...
Applies To Product(s): AutoPIPE Version(s): ALL; Area: Licensing Date Logged & Current Version May 2019 12.01.00.09 Problem: Trial mode displayed on BLT for AutoPIPE license, why and how to avoid?...
View ArticleWiki Page: 01. Batch Processing , also known as "Automated System...
AutoPIPE has the ability to perform analyses, and produce reports for a previously defined system database ( *.DAT ) without user interaction. This gives the designer the opportunity to concentrate on...
View ArticleWiki Page: 02. Troubleshooting Batch Processing / Automated Processing in...
1. Common mistakes 2. Suppress Gui and Warning messages 3. "Scan sub-directory for models" button is not working 4. Select a Seismic Anchor Movement analysis option See Also ATS and Batch Processing...
View ArticleWiki Page: 02. Bentley AutoPIPE Installation Test Set (ITS)
Bentley AutoPIPE 12.03.00.17 and higher provides Commercial users with an Installation Test Set (ITS), so they can verify proper operation of AutoPIPE program once it has been installed on a computer....
View ArticleWiki Page: Q. How soon will the ATS be ready for AutoPIPE version xxx?
Answer: It takes a considerable amount of time and effort to produce an Automated Test Set: new model creation, new supporting Mathcad's, updated documentation, updated software, Certifications, etc.....
View Article