Wiki Page: Q. What is the list of currently available ATS versions for AutoPIPE:
Answer: As of June 2021, current list of ATS or QA versions available for AutoPIPE are: Edition Version Number AutoPIPE CONNECT v.12.08.02.40 v.12.04.00.14 v.12.00.00.16 v.11.01.00.24 v.10.01.00.09...
View ArticleWiki Page: Q. Reference for equations and mathcads / hand calculations stated...
I am trying to locate the reference information for the equations used to validate the AutoPIPE software as stated in the ATS documentation. "THEORY: Refer to the AutoPIPE Reference Information in the...
View ArticleWiki Page: Q. Why are some models (ex.QA 262-6.dat) are not listed in the...
Answer: In the AutoPIPE ATS document (ap_ats.pdf), just before "Description of Acceptance Test Systems", is a note that reads" " * These test sets are not part of the published Acceptance Test Set...
View ArticleWiki Page: Q. The ATS Test Features Cross Reference includes many entries...
Answer: Please note the manual indicates the following: " * These test sets are not part of the published Acceptance Test Set Manual." The ATS is performed to verify the results of the application for...
View ArticleWiki Page: 03. How do I Install, License, and Run AutoPIPE ATS (Automatic...
Applies To Product(s): AutoPIPE Version(s): ALL Area: installation Original Author: Bentley Technical Support Group Date Logged & Current Version Dec 2014 09.06.01.10 Problem: How do I Install,...
View ArticleForum Post: RE: Release for hanger selection
Greetings, My humble apology, however this question is outside the scope for AutoPIPE TSG. Please see WIKI here for what is TSG. We should not be commenting on actual construction / installation...
View ArticleWiki Page: System Messages
Application Crash AutoPIPE Vessel Design and Calculations Error Intel(r) Visual Fortran run-time error Licensing Prodia2 Prodia2.exe Setup Warning
View ArticleWiki Page: Prodia2 - messages displayed in AutoPIPE Vessel
File last updated with build xxx which is newer than the current build. Some values might be missing. See Also System Messages AutoPIPE Vessel
View ArticleWiki Page: File last updated with build xxx which is newer than the current...
Applies To Product(s): AutoPIPE Vessel Version(s): ALL Area: Date Logged & Current Version July 2023 43.01.01.011 Problem: The following message is displayed when opening a file: File last updated...
View ArticleWiki Page: 06. Can different support groups access a scaled version of the RS...
Applies To Product(s): AutoPIPE Version(s): ALL; Area: Loads Date Logged & Current Version Aug 2022 12.08.01.010 Problem: "Once a RS is assigned to the program, can different support groups access...
View ArticleForum Post: RE: Error 401 - LOCAL LOADS ((Support)): L/2 - d -Cx < r/2 on...
Greetings, Please raise an service case and attach the model file (.emvd) so we can investigate on it. You can raise a service case from here . Regards, Tanaji Gaikwad Senior Technical Support Engineer...
View ArticleWiki Page: Batch Processing, ITS, and ATS using AutoPIPE
1. Batch Processing 2. ITS (Installation Test Set) - all users 3. ATS (Automatic Test Set) - only AutoPIPE QA users, see here a. Install, License, and Run instructions b. Release notes c. FAQ 4....
View ArticleForum Post: RE: Double pipe heat exchanger
Greetings, Double pipe heat exchanger design is not available in AutoPIPE Vessel. AutoPIPE Vessel can be used to design different type of equipment as follows, Shell & Tube Heat Exchangers Storage...
View ArticleWiki Page: 02. How you define a Seismic load combination in AutoPIPE?
Applies To Product(s): AutoPIPE Version(s): ALL; Area: Load case Date Logged & Current Version Aug 2023 23.00.00.230 Problem: How you define a Seismic load combination in AutoPIPE? Solution: To...
View ArticleWiki Page: 03g. "Occasional" - AutoPIPE load case
Comments, Questions, and Answers about performing a Fatigue analysis in AutoPIPE Item #1: Define an occasional load case Item #2: Define an Sesimic Load combination. See Also Loads and Load Sets...
View ArticleWiki Page: Q. How to run the Trial version of AutoPIPE Vessel?
Applies To Product(s): AutoPIPE Vessel Version(s): ALL Area: Date Logged & Current Version June 2018 40.06.00.07 Problem: How to run the Trial version of AutoPIPE Vessel? Solution: Download and...
View ArticleWiki Page: d. Incline - Support Type in AutoPIPE - FAQ's
Comments, Questions, and Answers about AutoPIPE's Incline Support Type: Item #1: Which direction is forward or backward on an Incline support, Rotation Support, or Snubber support in AutoPIPE? Item #2:...
View ArticleWiki Page: 06. How to model a support that has a breakaway force and then...
Applies To Product(s): AutoPIPE Version(s): ALL; Area: Modeling Date Logged & Current Version Dec 2022 12.08.03.015 Problem: How to model a support that has a breakaway force and then free to move...
View Article