Clik here to view.
Forum Post: Re: Seismic Fault line Crossing
Hello Jacky89,I do not know of any specific software features required for pipelines crossing a seismic Fault line beyond typcial burried piping and seismic analysis. Would you please provide specifics...
View ArticleClik here to view.
Wiki Page: E90-2: Analysis results do not exist
Applies To Product(s):AutoPIPE,Version(s):2004, XM, & V8iEnvironment: N/AArea: ErrorSubarea: Original Author:Bentley Technical Support GroupProblem:After conducting analysis I got error "E90-2:...
View ArticleClik here to view.
Wiki Page: AutoPIPE Errors
Topics under the heading should be based on Error messages found in AutoPIPE: E90-2: Analysis results do not existE512-65: the model cannot be openedE751-1 Tee type gt 8 or lt 1. SIF not calculated
View ArticleForum Post: Re: Autopipe v8i Plus: General shear stress and shear force output
Hello Whistler,As you already know the Shear stress is calculated for GENERAL and Stoomwezen Piping codes. Otherwise, The General Pipe Stress Report is produced by enabling the General Stress option in...
View ArticleForum Post: Re: Autopipe calcuate piping pressure thrust and pressure...
Thanks Samhuff for your reply,Yes, that is my mistake, Ai is inner area of pipe, I will change it,I had a situation is to model victaulic flexible coupling piping system, pipe directional anchor with...
View ArticleForum Post: Re: AutoPIPE's Most Wanted
1. technical reference manual is necessary, it can be any format, caear II has this pdf file in program folder (c2TR.pdf), Stess engineer need to know math behind calculation2. expanson joint modeler...
View ArticleClik here to view.
Forum Post: Re: Dynamic load factor
Hello Mykola,I apologize for the inconvenence, but AutoPIPE does not have a location to input a specific Dynamic Load Factor (DLF). However there are 3 options to consider for applying a scale...
View ArticleClik here to view.
Wiki Page: Bentley AutoPIPE Nozzle (WinNOZL)
Topics under the heading should be based on:All topics related to AutoPIPE Nozzle(previously known as WinNOZL)Installation PrintingShell Tab - under constructionNozzle Tab - under constructionReinf....
View ArticleClik here to view.
Wiki Page: System Tab - AutoPIPE Nozzle
Applies To Product(s):AutoPIPE Nozzle,Version(s):V8iEnvironment: N/AArea: ModelingSubarea: Original Author:Bentley Technical Support GroupQuestions:1. Does AutoPIPE Nozzle have metric and english...
View ArticleForum Post: Re: Model centre of gravity & weight
Helo Dweller, To answer your original question,Can you please advise how I can obtain the location of the model centre of gravity from AutoPIPE? and the total weight of the model?As,...
View ArticleClik here to view.
Wiki Page: Modeling - AutoPIPE
Topics under the heading should be based on:Component modeling with associated dialogsPlease see the following AutoPIPE help section: Help > Contents> Contents Tab> Modeling Approaches>...
View ArticleClik here to view.
Wiki Page: 7.Concentrated Forces
Applies To Product(s):AutoPIPE,Version(s):2004, XM, & V8iEnvironment: N/AArea: ModelingSubarea: Original Author:Bentley Technical Support GroupQuestions:Question 001: I have to input a whole bunch...
View ArticleForum Post: Pipe Supports, Buried Piping, and More on Insider Skills this Friday
Friday August 9th Insider Skills: AutoPIPE free seminar.This week’s topics will include:Support Options – Rigid, Steel, ConcreteBuried Pipe with Concrete Slab on TopRefractory Lined PipingSneak Peek...
View ArticleClik here to view.
Wiki Page: Trust Licensing - AutoPIPE V8i 9.6 and higher
Applies To Product(s):AutoPIPE, AutoPIPE NozzleVersion(s):2004, XM, & V8iEnvironment: N/AArea: Subarea: Original Author:Bentley Technical Support Group Problem:Does AutoPIPE or AutoPIPE Nozzle...
View ArticleForum Post: Re: AutoPIPE's Most Wanted
1. Slope presets. It would be nice to be able to just say all piping has an 1/8" slope and then draw the piping and the horizontal pipe is already sloped for you. You would be able to adjust the...
View ArticleForum Post: Re: Autopipe calcuate piping pressure thrust and pressure...
You mention a flexible coupling, and I have seen you mention Victaulic couplings in other posts. Are you attempting to take credit for the flexibility of those couplings in your analysis? I would...
View ArticleClik here to view.
Wiki Page: •Bentley AutoPIPE V8i 09.05.01.02 Acceptance Test Set
Applies To Product(s):AutoPIPE ATSVersion(s):2004, XM, & V8iEnvironment: N/AArea: InstallationSubarea: Original Author:Bentley Technical Support GroupBentley AutoPIPE V8i (SELECTseries 4...
View ArticleClik here to view.
Wiki Page: Bentley AutoPIPE Release Notes
The following Release Notes are provided as a reference by Bentley's Technical Support Group.Bentley AutoPIPELatest Major Version of AutoPIPEBentley AutoPIPE V8i SELECTseries 1 version...
View ArticleClik here to view.
Wiki Page: AutoPIPE ATS download / install instructions
Applies To Product(s):AutoPIPE ATSVersion(s):2004, XM, & V8iEnvironment: N/AArea: InstallationSubarea: Original Author:Bentley Technical Support GroupProblemHow to download and install Bentley...
View ArticleWiki Page: ATS and Batch Processing - AutoPIPE
Topics under the heading should be based on:Bentley AutoPIPE Automatic Test Set (ATS)General questions about the AutoPIPE ATSBatch ProcessingAutoPIPE ATS release notesAutoPIPE ATS download instructions
View Article