Forum Post: RE: AutoPIPE instability with nozzles
Hello Ettore, I do not see your attached file for review. Please load it to the Bentley FTP site and let me know the name of the file. Or Create a service request and send the file for review....
View ArticleForum Post: RE: Modeling a pipeline resting on gravel
Thanks Mike...I created 3 separate models using 0.3, 0.4 & 0.6 coefficient of friction and results indicate that the worst case is at the higher CoF of 0.6. See below for the table of Friction...
View ArticleWiki Page: 09. Nozzle Flexibility in AutoPIPE and AutoPIPE Nozzle
Applies To Product(s): AutoPIPE Version(s): 2004, XM, V8i Environment: N/A Area: Modeling Subarea: Original Author: Bentley Technical Support Group Date Logged & Current Version July 2015...
View ArticleWiki Page: 03b. Modeling Vessel / Nozzles in AutoPIPE
Applies To Product(s): AutoPIPE, Version(s): 2004, XM, & V8i Environment: N/A Area: Modeling Subarea: Original Author: Bentley Technical Support Group The following section will contain questions...
View ArticleForum Post: RE: Expansion Joint To Equipment - Pressure Thrust?
Hello ConstantEffort: Are you asking how to eliminate pressure thrust from an united expansion joint? Please consider the following WIKI here. Regards, Mike Dattilio Bentley Product Advantage Group...
View ArticleWiki Page: 01. Which direction is forward or backward on an Incline support,...
Applies To Product(s): AutoPIPE Version(s): 2004, XM, V8i Environment: N/A Area: Modeling Subarea: Original Author: Bentley Technical Support Group Date Logged & Current Version July 2015...
View ArticleWiki Page: d. Incline - Support Type in AutoPIPE - FAQ's
Applies To Product(s): AutoPIPE Version(s): 2004, XM, V8i Environment: N/A Area: Subarea: Original Author: Bentley Technical Support Group Date Logged & Current Version July 2015 09.06.02.06...
View ArticleWiki Page: 01. Different Types of Supports In AutoPIPE?
Applies To Product(s): AutoPIPE, Version(s): 2004, XM, & V8i Environment: N/A Area: Modeling Subarea: Original Author: Bentley Technical Support Group Dec 2014, AutoPIPE V8i 09.06.01.10 AutoPIPE...
View ArticleWiki Page: 01. How to export support node points coordinates from AutoPIPE to...
Applies To Product(s): AutoPIPE Version(s): 2004, XM, V8i Environment: N/A Area: Report Subarea: Original Author: Bentley Technical Support Group Date Logged & Current Version July 2015 09.06.02.06...
View ArticleWiki Page: 03-q: Model Input listing - "Support" sub-report in AutoPIPE
Applies To Product(s): AutoPIPE Version(s): 2004, XM, V8i Environment: N/A Area: Report Subarea: Original Author: Bentley Technical Support Group Date Logged & Current Version July 2015 09.06.02.06...
View ArticleWiki Page: Pressure Vessel Output Report Issues in AutoPIPE Vessel
Applies To Product(s): AutoPIPE Vessel Version(s): V8i Environment: N/A Area: Output report Subarea: Original Author: Bentley Technical Support Group Comments, Questions, and Answers related to...
View ArticleForum Post: RE: Take the Navigator CONNECT Test Drive
Well, I forgot to change project. That is why I did not find the sync icon. :)
View ArticleWiki Page: Bentley AutoPIPE Nozzle (WinNOZL)
Applies To Product(s): AutoPIPE Nozzle Version(s): V8i Environment: N/A Area: General Subarea: Original Author: Bentley Technical Support Group Attention: a. Table of Contents b. AutoPIPE Nozzle...
View ArticleComment on ASCE7 - 2010 Wind loads are Service or Ultimate loads in AutoPIPE
This is a non-answer. Is the reaction a service load reaction or an ultimate reaction? If AutoPipe doesn't reduce the wind speed internally then I'd think they're over-calculating the stress on the...
View ArticleWiki Page: Bentley AutoPIPE V8i SELECTseries 5 (v09.06.02.06) - maintenance...
Applies To Product(s): AutoPIPE, Version(s): V8i Environment: N/A Area: Installation Subarea: Original Author: Bentley Technical Support Group Date Posted: 4/3/2015 10:38:39 AM Platforms: Windows 7...
View ArticleWiki Page: ASCE7 - 2010 Wind loads are Service or Ultimate loads in AutoPIPE
Applies To Product(s): AutoPIPE, Version(s): 2004, XM, & V8i Environment: N/A Area: Subarea: Original Author: Bentley Technical Support Group Problem: Up 'til now, we had been using ASCE 7-02...
View ArticleFile: AutoPIPE V8i (SELECTseries 5) Maintenance Release 2 (Version 9.6.2.6)...
AutoPIPE V8i (SELECTseries 5) Maintenance Release 2 (Version 9.6.2.6) 简体中文自述文件
View ArticleForum Post: Webinar: Offshore and Subsea Pipelines with AutoPIPE
Join us for a complimentary live webinar: Offshore and Subsea Pipelines with AutoPIPE. AutoPIPE is the most comprehensive piping analysis software for small to high-end piping projects worldwide....
View ArticleWiki Page: 06. What value of Bend radius is AutoPIPE using when calculating...
Applies To Product(s): AutoPIPE Version(s): 2004, XM, V8i Environment: N/A Area: Subarea: Original Author: Bentley Technical Support Group Date Logged & Current Version July 2015 09.06.02.06...
View ArticleWiki Page: ASME B31.1 Piping Code Calculation Issues
Applies To Product(s): AutoPIPE, Version(s): 2004, XM, & V8i Environment: N/A Area: Subarea: Original Author: Bentley Technical Support Group Comments, Questions, and Answers about ASME B31.1...
View Article