Forum Post: RE: References for the force acting on the + and - sides of a point
Hello RKP, Please see the following AutoPIPE help section: Help > Contents> Contents Tab> Reference Information> Results Interpretation> Pipe Forces and Moments: Global Option Regards,...
View ArticleForum Post: RE: References for the force acting on the + and - sides of a point
Hi Mike, Thank youfor the help! Now It's clear! The same reference (that coincides with the global reference) is used on both sides. In fact the discontinuity in the internal vertical force is 2234-...
View ArticleForum Post: RE: Guide support modeling
Correct, This is the top of the steel member, so need to be there to reflect the secondary suport flexibility - very usefull feature 'by the way' and of course is not the node of the pipe, and of...
View ArticleForum Post: RE: Guide support modeling
There is one issue that should be considered: what is the material between clamp and pipe - assuming this picture is close to reality...
View ArticleWiki Page: 04. AutoPIPE Stress Isometric Troubleshooting: Table Issues
Applies To Product(s): AutoPIPE Version(s): 2004, XM, V8i Environment: N/A Area: Isometric Drawing Subarea: Original Author: Bentley Technical Support Group Date Logged & Current Version Oct. 2015...
View ArticleWiki Page: 22. Stress Isometric - Enhancements for AutoPIPE
Applies To Product(s): AutoPIPE, Version(s): 2004, XM, & V8i Environment: Enhancements Area: Subarea: Original Author: Bentley Technical Support Group The following Flange Analysis enhancements...
View ArticleWiki Page: 01. Stress Isometric table shows a different piping code than in...
Applies To Product(s): AutoPIPE Version(s): 2004, XM, V8i Environment: N/A Area: Isometric table Subarea: Original Author: Bentley Technical Support Group Date Logged & Current Version Oct. 2015...
View ArticleWiki Page: ASME BPV-III-1-NB, AutoPIPE Nuclear Piping Code FAQ
Boiler & Pressure Vessel Code, Rules for Construction of Nuclear Power Plant Components Division 1, Subsection NB, Class 1 Components Applies To Product(s): AutoPIPE, Version(s): 2004, XM, &...
View ArticleWiki Page: 01. Why does AutoPIPE apply the square root only “partially” when...
Applies To Product(s): AutoPIPE Version(s): 2004, XM, V8i Environment: N/A Area: Subarea: Original Author: Bentley Technical Support Group Date Logged & Current Version Oct. 2015 09.06.02.06...
View ArticleWiki Page: 05. Piping Code Calculations - AutoPIPE
Applies To Product(s): AutoPIPE, Version(s): 2004, XM, & V8i Environment: N/A Area: Subarea: Original Author: Bentley Technical Support Group Item #1, Comment: Be sure to review the following...
View ArticleWiki Page: 02. Why does the results grids not show the SNiP 1997 Hoop Stress...
Applies To Product(s): AutoPIPE Version(s): 2004, XM, V8i Environment: N/A Area: Calculation Subarea: Original Author: Bentley Technical Support Group Date Logged & Current Version Oct. 2015...
View ArticleWiki Page: SNIP Piping Code Calculation Issues in AutoPIPE
Applies To Product(s): AutoPIPE Version(s): 2004, XM, V8i Environment: N/A Area: Subarea: Original Author: Bentley Technical Support Group Date Logged & Current Version Oct. 2015 09.06.02.06...
View ArticleForum Post: RE: There are no listed allowable hoop stress SNiP
Hello Sergey, Please see the following WIKI page:...
View ArticleForum Post: Is there someone familiar how to group SAM displacements? I have...
Is there someone familiar how to group SAM displacements? I have same 9 support with different elevations. So I input all the interpolated SAM for each supports base on each elevation , case S1(OBE...
View ArticleForum Post: E801-24: Number of MSRS groups is inconsistent with SAM case
How to fix this kind of error message? "E801-24: Number of MSRS groups is inconsistent with SAM case"
View ArticleWiki Page: 03. When calculating ratchet allowable, is Sy the minimum from...
Applies To Product(s): AutoPIPE Version(s): V8i Environment: N/A Area: Subarea: Original Author: Bentley Technical Support Group Date Logged & Current Version Oct. 2015 09.06.02.06 Problem: It has...
View ArticleForum Post: Captured modal mass in Fluid Transient analysis
Hi, In Fluid transient analysis, the capatured modal mass seems cannot be changed from the modal analysis. As a example below: TIME HISTORY LOAD CASES : ------------------------- Number of load cases...
View ArticleWiki Page: E801-24: Number of MSRS groups is inconsistent with SAM case -...
Applies To Product(s): AutoPIPE Version(s): 2004, XM, V8i Environment: N/A Area: Subarea: Original Author: Bentley Technical Support Group Date Logged & Current Version Oct. 2015 09.06.02.06...
View ArticleWiki Page: Error Messages displayed in AutoPIPE
Applies To Product(s): AutoPIPE, Version(s): 2004, XM, & V8i Environment: N/A Area: Error Messages Subarea: Original Author: Bentley Technical Support Group AutoPIPE Preview Handler error on...
View ArticleForum Post: RE: E801-24: Number of MSRS groups is inconsistent with SAM case
Hello Ellie, Please see the following WIKI here: communities.bentley.com/.../24840.e801-24-number-of-msrs-groups-is-inconsistent-with-sam-case-error-message-in-autopipe Regards, Mike Dattilio Bentley...
View Article