Forum Post: Guide support modeling
Hi, Please help me. I would like to model guide support for cryogenic pipeline like on the sketch below. The guide support is 300 mm lenght. Shall I model as two guide supports with spacing 300 mm...
View ArticleForum Post: RE: Guide support modeling
That's how I would go about it. I may even stick a support mid span between the outer supports as well to ensure any deflections of the piping does not exceed the boundary condition of the actual support.
View ArticleWiki Page: W97-99: No analyzed pressure cases present. Only axial GR stress...
Applies To Product(s): AutoPIPE Version(s): 2004, XM, V8i Environment: N/A Area: Subarea: Original Author: Bentley Technical Support Group Date Logged & Current Version Oct. 2015 09.06.02.06...
View ArticleForum Post: RE: W99-97: No analyzed pressure cases present. Only axial GR...
Hello Diana, Please see the following WIKI here: communities.bentley.com/.../7410.warnings-messages-displayed-in-autopipe Regards, Mike Dattilio Bentley Product Advantage Group Analyst...
View ArticleWiki Page: Warnings Messages displayed in AutoPIPE
Applies To Product(s): AutoPIPE, Version(s): 2004, XM, & V8i Environment: N/A Area: Warning Subarea: Original Author: Bentley Technical Support Group W21-38: This function cannot be applied at the...
View ArticleForum Post: Stress ISO possibilities
Hello The company I have been working for use Autopipe Advanced version 09.06.02.06. Is it possible by using Stress ISO to generate the iso drawings with bill of materials in AutoCAD based on the 3D...
View ArticleComment on After-forming Thickness
So "tn" is the final thickness after forming? If it's so, then UG-79-1 make the wrong calculation, because tn there is the nominal thk. bebore forming... Also is there a way to indicate the thickness...
View ArticleForum Post: Autopipe Stress Iso
Hello The company I have been working for use Autopipe Advanced version 09.06.02.06. Is it possible by using Stress ISO to generate the iso drawings with bill of materials in AutoCAD based on the 3D...
View ArticleForum Post: RE: Autopipe Stress Iso
Hi, AutoPIPE Advanced, starting from release 09.06.02.06 works with OpenPlant Isometrics Manager, so, to generate StressISO it is advisable to Save As to previous version of AutoPIPE, assuming you have...
View ArticleForum Post: RE: Guide support modeling
I am for this solution. Please bear in mind that to make things easier you should build a model of secondary suport, e.g. vertical steel element, then both guides attach to the same endpoint of the...
View ArticleWiki Page: How to model a insulated pipe support in AutoPIPE?
Applies To Product(s): AutoPIPE Version(s): 2004, XM, V8i Environment: N/A Area: Subarea: Original Author: Bentley Technical Support Group Date Logged & Current Version Oct. 2015 09.06.02.06...
View ArticleWiki Page: 01. Different Types of Supports In AutoPIPE?
Applies To Product(s): AutoPIPE, Version(s): 2004, XM, & V8i Environment: N/A Area: Modeling Subarea: Original Author: Bentley Technical Support Group Dec 2014, AutoPIPE V8i 09.06.01.10 AutoPIPE...
View ArticleForum Post: RE: Stress ISO possibilities
Hello robert, Please see the following post: communities.bentley.com/.../112632 Regards, Mike Dattilio Bentley Product Advantage Group Analyst ===================================================
View ArticleForum Post: RE: Autopipe Stress Iso
Hi Thanks for your advice. In the end of the next week I will try to download OP Isometrics Manager to check how it works for Autopipe Advanced. In case of any problem to generate isometrics drawings...
View ArticleForum Post: RE: Autopipe Stress Iso
Please, take into account that this is not kind of BOM as it is expected from OpenPlant/AutoPlant. Rather stressiso style...
View ArticleForum Post: RE: Autopipe Stress Iso
Is it means that OP Isometrics Manager will not create BOM as it is expected in detailed drawing (rysunek projektu wykonawczego części technologicznej)? If not, is it the way to export iso drawing to...
View ArticleForum Post: RE: Guide support modeling
Maciej thank you for the suggestion. I have one more question regarding your solution. I assume that point 5104 is not connected to pipe. What about imposed displacement of support when is not...
View ArticleForum Post: There are no listed allowable hoop stress SNiP
Good morning! I'm trying to do a calculation using SNiP 2.05.06-85* and have some questions about results. This is a screen of my results window. I don't understand why there are no reluts for...
View ArticleForum Post: References for the force acting on the + and - sides of a point
Hi all, I have a beginner-level question, let's consider a point, say A10, wich rests on a +Z (upward positive) vertical support. The support exterts +3845 N on that point. Looking at the report I see...
View ArticleForum Post: RE: Guide support modeling
Hello Pawel, Yes, you can add impose support displacement to this support. Add it to the Anchor at 5103 in Maciej image above. Regards, Mike Dattilio Bentley Product Advantage Group Analyst...
View Article