Wiki Page: 09. Gasket Effective width does not match the ASME code value in...
Applies To Product(s): AutoPIPE Version(s): V8i Area: Flange analysis Original Author: Bentley Technical Support Group Date Logged & Current Version Mar. 2015 09.06.01.11 Problem: I am doing ANSI...
View ArticleWiki Page: 11. Why does Max Ratio = 0.00 and Notes = Fail for flange in...
Applies To Product(s): AutoPIPE Version(s): ALL; Area: Flange analysis Original Author: Bentley Technical Support Group Date Logged & Current Version Nov. 2016 10.01.00.09 Problem: Why does Max...
View ArticleWiki Page: 04. What is the difference between the "Operating Condition" and...
Applies To Product(s): AutoPIPE Version(s): 2004, XM, V8i Environment: N/A Area: Resport Original Author: Bentley Technical Support Group Date Logged & Current Version Jan 2015 09.06.01.10 Problem:...
View ArticleForum Post: RE: Flange analysis per EN 1591-1
Hi Mike, Please do so, this would be an exciting feature of hwich I hope it will be available soon to use. Regards
View ArticleWiki Page: 12. Soil Load Enhancements & Defects for AutoPIPE
Note: if an enhancement or defect has not been added to the program, log an Service request for that enhancement. The more requests logged per an enhancement, the quicker the CAE development team will...
View ArticleWiki Page: 07. Flange Analysis Enhancements & Defects for AutoPIPE
Note: if an enhancement or defect has not been added to the program, log an Service request for that enhancement. The more requests logged per an enhancement, the quicker the CAE development team will...
View ArticleForum Post: B31.3 material stress allowables
Im using AP v 11.02.00.10 for a pipe stress analysis. The analysis under consideration is a piping system designed to B31.3 2016. Im using the AUTODIN library (since I need to model EN 1092-1 flanges),...
View ArticleWiki Page: "Alert" Messages displayed in AutoPIPE
Item #1: File [c:\User\...\drawing name] does not exist Also See Warnings, Errors, Crashed, Confirm Messages
View ArticleWiki Page: "Autopipe.exe" Messages displayed in AutoPIPE
The following messages appear in AutoPIPE: Item #1: "The application failed to initialize properly (0xc0150002)" Item #2: autopipe.exe - No Disk There is no disk in the drive. Please insert a disk into...
View ArticleWiki Page: "Bolts*" Messages displayed in AutoPIPE
The following messages appear when running AutoPIPE program: The value cannot be greater than flange outside diam. minus bolt hole diam. Also See: Warnings, Errors, Crashed, Confirm Messages in AutoPIPE
View ArticleWiki Page: "Confirm" Messages displayed in AutoPIPE
FAQ's about Confirm Messages in AutoPIPE Item #1: This model may be affected by a previous program defect Item #2: Current model revision does not match analysis result(s) below Item #3: The load case...
View ArticleWiki Page: "Error" Messages displayed in AutoPIPE
AutoPIPE Preview Handler error on installation Closed loop detected in imported model at TEE point XXX. E15-13: PXD file is needed for accessing AutoPLANT data in this model Please place PXD and PXH...
View ArticleWiki Page: "Flange*" Messages displayed in AutoPIPE
The following messages appear when running AutoPIPE program: Item #1: "The value must be equal to the inside diameter of the pipe" Item #2: "The value must be equal to the outside diameter of the pipe"...
View ArticleWiki Page: "License Management Tool" Messages displayed in AutoPIPE
"An Error has occured while attempting to verify the server and activation key" See Also Warnings, Errors, Crashed, Confirm Messages in AutoPIPE Bentley AutoPIPE
View ArticleWiki Page: "Note" Messages in AutoPIPE
"Note" Messages displayed in AutoPIPE N13-83: Pressure extension has been enabled in the analysis N15-12: Cannot find library associated with the model N24-24: Distributed load can only be deleted from...
View ArticleWiki Page: "Visual Fortran run-time error" messages displayed in AutoPIPE
Forrtl: severe (9); permission to access file denied, unit 10 Forrtl: severe (9): permission to access file denied, unit 121 Forrtl: severe (24): end-of-file during read, unit 11, file c:\progra...
View ArticleWiki Page: "Warnings" Messages displayed in AutoPIPE
W21-21: Cannot perform this operation, multiple points selected W21-32: Cannot split segments, maximum number of segments reached W21-34: This function can only be applied on junction of two segments...
View ArticleWiki Page: "Bentley AutoPIPE" Messages displayed in AutoPIPE
Error opening file: xxxx.L001 Error Writing Files H/D is greater than 14.0 Please Analyze the Model First. The Load Table values can only be set if modal analysis results exist Please select a valid...
View ArticleWiki Page: Warnings, Errors, Crashed, Confirm Messages in AutoPIPE
From time to time something will happen where AutoPIPE may display a message pop-up text box. Most of these typical warnings are categorized by the text box labels below, select the hyper link to see...
View Article