Forum Post: RE: DNV 2012-Load Combination
JackBP/AYMAN79: I could not find any files attached to the post. AutoPIPE calculates the allowable for Pressure containment category using equation 5.6 under D200 of section 5 for DNV F101 (2012)....
View ArticleFile: PULS - general information
Please see the attached document for general information about PULS.
View ArticleForum Post: RE: Stresses for occasional loads - Elevated Temperature Fluid...
Hi Mike, thanks for the swift reply. By referring to para 302.3.6(a), I meant to say the Code Im referring to is ASME B31.3. I think I missed something before posting my image (I did check AutoPIPE...
View ArticleForum Post: RE: Stresses for occasional loads - Elevated Temperature Fluid...
Hello HVN, Yes. Regards, Mike Dattilio Bentley Technical Support Analyst Web: selectservices.bentley.com Create your Service Request online! Log in to SELECTservices Online via...
View ArticleWiki Page: W2018-11, W2018-12, W2018-16: Not authorized for ???? edition
Applies To Product(s): AutoPIPE, Version(s): 2004, XM, & V8i Environment: N/A Area: Licensing Subarea: Original Author: Bentley Technical Support Group Problem: The following appears when starting...
View ArticleWiki Page: Stress Iso Troubleshooting Tips for AutoPIPE
Comments, Questions, and Answers with AutoPIPE Stress ISO. In addtion to the "StressISO_Troubleshooting.pdf" document found on your hard drive, see the following information: Isogen is a 3rd party...
View ArticleWiki Page: Modeling In PULS
Applies To Product(s): PULS Version(s): XM & V8i Environment: N/A Area: modeling Subarea: Original Author: Bentley Technical Support Group Comments, Questions, and Answers about modeling with...
View ArticleWiki Page: Bentley PULS
Topics under the heading should be based on: Bentley PULS Op1, Op2, or Op3 Product Data Sheet Installation Error Messages Modeling In PULS Calculations in PULS Results in PULS PULS program stops working
View ArticleWiki Page: AutoPIPE Compressor Vibration Method
Applies To Product(s): AutoPIPE Version(s): all Environment: N/a Area: Dynamic Subarea: N/A Original Author: Mark Upston, Bentley Technical Support Group...
View ArticleForum Post: RE: DNV 2012-Load Combination
Hi Bilal Shah, Your answers are very clear. Thank you for your help!
View ArticleWiki Page: FAQ's - Specific to Shell and Tube Heat Exchangers in AutoPIPE Vessel
Applies To Product(s): AutoPIPE Vessel, Version(s): V8i Environment: N/A Area: FAQ Subarea: Original Author: Bentley Technical Support Group Comments, Questions, and Answers: Question #1: What can I...
View ArticleForum Post: RE: Stresses for occasional loads - Elevated Temperature Fluid...
Mike, thanks again. Great support!
View ArticleForum Post: Applying WJSRF's
Im currently employing some pipe stress analysis on a hot line. Since Id like to 'refine' my model as much as possible, Ive inserted a lot of extra points. These points dont represent any welds. My...
View ArticleForum Post: RE: Applying WJSRF's
Hello HVN, Please see the following AutoPIPE help section: Help Contents Search Tab enter "Weld Factor" (include the quotes), press List Topics button, double click on the selected topic from the list...
View ArticleForum Post: B31.3 default allowables
All, I was trying to find out the methodology behind autopipe default allowable for ASME B31.3 to no avail. Anyone able to shed some light?
View ArticleForum Post: RE: Applying WJSRF's
Hi Mike, Thanks for the reply. Can you confirm if the statement in my OP is correct?
View ArticleForum Post: RE: Applying WJSRF's
Hello HVN, Your original question: " I tried to determine how one should include WJSRF's at the piping welds Here's what I found of how I think it should be inserted at only those locations that...
View ArticleForum Post: RE: B31.3 default allowables
Hello Lenie666, I do not understand what you mean by "methodology behind default allowable". The allowables are calculated per the piping code selected. In your case that would be, ASME B31.3....
View Article